This post following next about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is quite enlightening. Read it yourself and decide what you think about it.
Setting up a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably tough job. If the old bathtub is readily available, the project can move immediately; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also set in the new one. Ensure you have certified on your own for the task and also fit trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually currently purchased a new tub and also do not need to change the setup of your previous water system pipes.
Your devices as well as material checklist need to consist of the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Flexible Wrench
- Putty Knife
- Screwdriver
- Cold Chisel
- Measuring tape
- Pipe Caps
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. When the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and also tighten them if essential. Fill up the bathtub and additionally inspect the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the bathtub needs to wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the market. It is recommended to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads on Tools You Need to Install a New Bathtub , I imagined sharing that excerpt was a good thing. You should take the time to share this post if you enjoyed reading it. Many thanks for going through it.
Suggested Site
Comments on “Exactly How to Install a Bath Tub Yourself”